MicroCare Tech Acupuncture Pen┐
Dual Mode 5 MW Laser Pen┐
AcuSmith V 2.0┐
Pointer Pulse┐
Acu Machine - 4 Output┐
Acu Machine - 6 Output┐
Acu Navigator┐
Digital Electro Acupunctoscope┐
Electro-Acupuncture Machine┐
IC-1107+ Electro-Acupuncture Device┐
WQ-6F Electro-Acupuncture Machine┐
Pointer Plus Excel II┐
Stim Plus II - Acupoint Location┐
Acu-Treat┐

AcuSmith V 2.0
TCM Reading, Detection, Treating and More

The AcuSmith V 2.0 utilizes a unique electronic acupuncture probe that reads, detects and treats general human conditions based on traditional Chinese medicine theory in terms of meridians and acupoints. The whole procedure is completed through pinpointing the specific areas that need care over your palm within a few minutes. Give it a try and be amazed by the result!

It also uses different methods to apply TCM through acupuncture, cupping, scraping, massage and more.

Features at a glance:

• Built-in LCD screen displays information about reading, detecting and treating.

• Used to predict your problems and treat the problems you may already have. 

• Kit including device, self adhesive patches, charts, battery and more.

• 9.25” x 6.75” x 2”

• Details available in the User’s Manual

<click> to enlarge»

Buy Now!
$159 + shipping*

Handheld Pulsed Laser and Pulsed TENS

The next generation handheld locator/stimulator! The Pointer Pulse is the first all-in-one unit that combines infrared laser therapy with electrical stimulation, allowing both methods of treatment to be used simultaneously. With its ergonomic design and single grounding plate, this device can easily be used with either the left or right hand. Electrical stimulation is initiated with a push button, while stimulation intensity is controlled with a dial. The 650 nm, 5 mW laser is controlled by a toggle switch where you can select from three modes: on (continuous laser beam), pulsed (10 Hz pulsed laser beam) and off (no laser beam). Accessories include a hand ground pole with attached wire, 9 volt battery, small screwdriver (for adjusting point location sound level), carrying case, and instructions.

<click> to enlarge»
 

Our Price:
$299 + shipping*

The all new and improved Acu Machine features an indicator for sound and luminescent state, a timing switch, a power voltmeter, a music device playing when the treatment is over or before it starts and an operating output protection.

         Features:

• The output pulse waves of the machine are in low voltage, low frequency.
• There are five types of pulse waves to be selected: continuous wave, dense-disperse wave, intermittent wave, ripple wave and respiration wave
• Four kinds of wave combinations can be used at the same time, separately, or get the two output or more crossed to use.

  Technical data:

• Continuous wave: pulse duration = 0.5ms; repeated pulse frequency: f1=1Hz – 100Hz.
• Dense-disperse wave: Dense-disperse wave displays alternatively, disperse frequency is f1 same as base wave; dense frequency is about 100Hz; pulse duration is 0.5ms; FREQ2 regulates the frequency f2 of 10-40 cycles per minute.
• Intermittent wave: Pulse shows at regular interval at a frequency of 10-40 cycles per minute.
• Ripple wave: Its amplitude increases to maximum and drops suddenly, and repeats the process.
• Respiration wave: Its amplitude increases first, then drops quickly to zero, and repeats this process.
• Ripple wave: Its amplitude increases to maximum and drops suddenly, and repeats the process

808-II comes with 4 outputs, 8 wire clips that can be used on 8 acupoints at the same time.

<click> to enlarge»

Our Price:
$139 + shipping*

The all new and improved Acu Machine features an indicator for sound and luminescent state, a timing switch, a power voltmeter and an operating output protection.

        Features:

• The output pulse waves of the machine are in low voltage and low frequency. There are five types of pulse waves to be selected. Continuous wave, dense-disperse wave, intermittent wave, ripple wave and respiration wave.
• Four kinds of wave combinations can be used at the same time, separately and get the two output or more crossed to use.

Technical data:

• Continuous wave: pulse duration = 0.5ms; repeated pulse frequency: f1=1Hz – 100Hz.
• Dense-disperse wave: Dense-disperse wave displays alternatively, disperse frequency is f1 same as base wave; dense frequency is about 100Hz; pulse duration is 0.5ms; FREQ2 regulates the frequency f2 of 10-40 cycles per minute.
• Intermittent wave: Pulse shows at regular interval at a frequency of 10-40 cycles per minute.
• Ripple wave: Its amplitude increases to maximum and drops suddenly, and repeats the process.
• Respiration wave: Its amplitude increases first, then drops quickly to zero, and repeats this process.

KWD 808-I comes with 6 outputs, 8 wires with alligator clips that can be used on 8 acupoints individually or all together at the same time to apply acupuncture needle treatment; and it is also equipped with 4 self-adhesive electrodes that can be used to apply electrical stimulation without using acupuncture needles.

Note:  D/C (9 V) is accessible with 6 x “C” CR14 UM2 Batteries (not included).

<click> to enlarge»

Our Price:
$189 + shipping*

Traditional Chinese Medicine believes that, if a condition manifests inside the body, the signs of that condition will also manifest outside the body. If the Chi (body’s own energy) flows inside the body, there will be no pain. If the Chi is blocked, there will be pain. The Chinese health researchers have found that the internal organs will reflect the state-of-Chi (flow or block) to the acupuncture points on the skin from the meridians and the collateral channels through different sensations under the same electric current. They also found that the acupuncture points on the hands are typically an excellent area of the body to observe the state-of-Chi.

Acu-Navigator is innovated on the basis of the above universal TCM theory and has put those principles into clinical practice. It is a quite accurate, indispensable, yet affordable machine which has made the four TCM techniques “Observation, Auscultation, Inquiry and Palpation” easy to learn and master.

Acu-Navigator is a unique electronic detecting tool that locates Chi blocks by using a Detecting Probe to check the acupuncture points on the hands. It is also a treating tool that clears those blocks by using Electricity, Magnetism, Sound and Light! Easy, safe and convenient to learn and operate, the Acu-Navigator is an essential tool and a must for acupuncturists, chiropractors, physical therapists, massage practitioners and TCM students.

Main Features:

• Quickly select the Palm Lines
• Easily Identifies the Five Body Systems
• Uses Electricity, Magnetism, Sound and Light

Major Technical Data:

• Voltage: 3 V.D.C (D Battery x 2)
• Pulse Frequency: 0.4 – 0.8 KHz
• Voltage Range of Pulse: 0.1 V. – 6 V.
• Output Load: 500 ohms
• Voltage (Unloaded-Peak Value): < 500 V
• Pulse Output (Maximum) > 7 uC
• Pulse Energy (Maximum – Single Pulse): < 30 mJ
• Size: 16” L. x 11” W. x 4” H.
• Weight: 7 lbs

Caution: These statements have not been evaluated by the Food and Drug Administration. This product is not intended to diagnose, cure, treat or prevent any disease.

<click> to enlarge»

 

$449 + shipping*

<click> to enlarge»
 

Our Price:
$249 + shipping*

The Multiple Electronic Acupunctoscope (MEA), Model WQ-10D1 is an instrument used both as a detector of acupuncture points and as an electrical stimulator for acupuncture therapy and anesthesia. The WQ-10D1 model is a newly modified unit from the older WQ-10 series acupunctoscope, featuring a CA (constant amplitude)-AM (amplitude modulation) selecting switch to allow it to discharge six different combinations of wave patterns.

I. Frequency f(c/s) 0~100 / Width T (µs) 250 ~ 400:

     The adjustment of the stimulating wave forms and frequencies.
They are controlled by following knobs and switch: F1=fixed
frequencies, F2=variable frequencies, CA (constant amplitude)
-AM (amplitude modulation) selecting switch, CA (constant
amplitude)-AM (amplitude modulation) selecting switch. There
are six different forms of combinations by using f1 and f2 CA-AM

1. When f2 is at 0, by adjusting f1, a continuous (CA) or rise-fall (AM) wave is obtained.

2. When f1 is at 0, by adjusting f2, an intermittent (CA) or saw tooth (AM) wave is obtained.

3. By adjusting f1 and f2, but keep f1<f2, a composite wave of alternating frequencies f1 and f2 a dense – disperse (CA) or rise dense- fall disperse (AM) wave is obtained.

II. Acupuncture therapy and anesthesia:

1. Set “Intensity” knob to zero and “E-E or APD” switch to “1.2.3”, set “Hi-Lo” switch to “Hi” or “Lo” position as required. Intensity of “Lo” position is 1/3 of “Hi”.

2. Plug output leads into 1.2.3 sockets, then fasten their clips to the handles of the needles.

3. Set the desirable waveforms and frequencies with knobs f1, f2 and K.

4. Turn “on” main switch

5. Adjust intensity to appropriate degree  

III. Therapy with Electric, Excitatory (E-E) and skin sure face acupuncture point stimulation:

1. Use output leads with banana plugs. Connect the bananas plugs with probes provided with cup shaped electrodes at terminal ends. Fill the cup with absorbent cotton soaked with salt solution. Fix the cup electrode onto the acupuncture points or the other selected parts of the skin. Set “Hi-Lo” switch to “Hi” position.

2. In case of weak stimulation follow the same steps described in II. Plug output leads into 1.2.3 sockets.

3. For strong stimulation, the output will be taken from the “E-E or APD” socket, which is specially designed for this purpose. Set” E-E or APD” switch to “E-E1+2+3” position and intensity is regulated by 1.2.3 channels together.

IV. Multiple usages:

1. The section used for acupuncture point detection can also be used for locating the auriculo-acupuncture points, meridian points, and band of (?) zone of acupuncture points.
2. The section used for stimulation can also be used for acupuncture therapy, skin surface acupuncture point stimulation, electrical Ti-Needle, acupuncture anesthesia, therapy by electric excitation, and measuring the sensitivity of meridian. Both A and B sections maybe used at the same time.
3. Multiple transmit messages:

     The instrument can transmit three waveforms of impulse series. Their frequency varies from 0- 100 C/S, with several adjustment combinations. By varying the combinations of these differing massage types, a large number of stimulating conditions may be derived in order to prevent repetitious overuse, enhancing therapeutic efficiency.

4. High intensity of output: divided into "High" and "Low" two ranges, smooth adjustment, high stability and low power consumption.
5. Detecting acupuncture points with accuracy and without producing pain sensation. After the location of point, stimulating pulses can also provide therapy from the detecting probe.

<click> to enlarge»

 

$199 + shipping*

The model IC-1107+ is a compact, lightweight, sturdy, palm-size, high quality Japanese electro-therapy device. A Hi/Low switch on the back of the unit facilitates use with needles (Low voltage setting) or MEA electro-therapy (Hi voltage setting). Offers 3 independently controlled output channels with adjustable frequency indicated by flashing light. This unit is not equipped with a point locator. Features a unique biphasic pulse form which has been designed to minimize electrolysis damage to the needle. The pocket portable IC-1107+ is the smallest and smartest looking professional electro-therapy unit in the world, for use in or out of the office.

Accessories include 3 sets of new CE wire leads with rectangular CE jack, carrying case, belt clip, 9 volt battery, and instructions.

Converter Jack (sold separately) converts rectangular CE jack to 3.5mm jack for use with all 3.5mm jack accessories.

Note: When using 9-volt Duracell Batteries with the IC-1107, a thin shim (or paper) must be placed at the bottom of the battery to make proper contact (ie.., Duracell are shorter in length). Also, in order to use the built-in battery check (located on the back side of unit), power must be turned on.

<click> to enlarge»

Our Price:
$249 + shipping*

The WQ-6F (57-6F) Electronic Acupunctoscope is an advanced apparatus specially designed and modified on the basis of Model 57 - 6D and WQ - 10C . It is based on recent results of theoretical research work and clinical practices in acupuncture therapy and anesthesia. It is the newest product of the 2nd-generation line of Transistor Electronic Acupunctoscope in China at present, and has the following features:

1.      Multi-purpose: The apparatus can be used in acupuncture therapy, acupuncture anesthesia, needleless therapy, measurement of the sensitivity of meridian and for physiological experiments etc.

2.      2 Multiple transmit messages

3.      The apparatus transmits eight different waveforms of impulse series. Their frequencies vary from 0 - 20c/s, 0 - 200c/s with continuous adjustment and multiple possible combinations.

4.      The apparatus consists of two independent sections (A and B) with seven channels. It is possible to select two different frequencies (A and B) and output waveforms simultaneously.

5.      3 High amplitude of output, divided into "High" and "Low" ranges, smooth adjustment, high stability and low power consumption, non-interference between channels, parallel or serial connection of output terminals to enhance stimulation for various purpose

I. The adjustment of stimulating waveforms and frequencies. Amplitude:

There are two types, as selected: constant amplitude (CA) or amplitude modulation (AM) switch.

II. Acupuncture therapy and anesthesia:

(1) Set "Amplitude" knobs to zero and all output controlled switches to separate positions (as 1, 2). Set "Hi - Lo" switch to "Hi" or "Lo" position as required. Amplitude of "Lo" position is 1/3 of "Hi". (2) Plug output leads into sockets (1 - 7), fasten their clips to the handles of the needles. (3) Set the desirable waveform and frequencies (f1, f2, m, CA, AM). (4)Turn "ON" main switch. (5) Adjust amplitude to appropriate degree. (6) Select parallel (1//2, 3//4) or series (5 + 6 + 7) connection as required, while amplitude is regulated by these knobs simultaneously.

III. Needleless therapy (1) Use needleless therapy electrode. Fill the cup of electrode with absorbent cotton soaked with salt solution. Attach the electrode onto the acupuncture point. Set "Hi - Lo" switch to "Hi" position. (2) In case of weak stimulation follow the same steps described in 2, outputs taken from sockets 1-7 (3) For strong stimulation, the output will be taken from the socket marked " • " , Set output controlled switch of 5 , 6 , 7 channels to 5 + 6 + 7 position and the amplitude is regulated by 5 , 6 , 7 channels simultaneously.

<click> to enlarge»
 

Our Price:
$249 + shipping*

Accessories:

• Output leads with electrodes 1 set
• Output leads with clips 7sets
• Monitoring loudspeaker 1 pc
• 1 artificial leather carrying case
• 1 instruction manual

Notes: The WQ-6F can emit 2 waveforms simultaneously, 1 from section A and 1 from section B. 7 channels do not interfere each other, but you can connect outputs in parallel or in succession to enhance stimulation for various purposes. When channels are connected in parallel, the output current is enhanced while the output voltage maintains the same. When channels are connected in succession, the output voltage is enhanced while the output current maintains the same.

The Pointer Plus Excel is the latest and most advanced user-friendly hand held point locator and stimulator. Features a built-in, 0.35" x 1.0" LCD digital display meter for location of acupuncture and trigger points.

The Pointer Plus Excel unit offers sensitive acu-point or trigger point location and stimulation. Location and stimulation are independently adjusted with two separate control dials.

This new Pointer Plus Excel device also includes more advanced features.

• The frequency is adjustable (1 to 16 Hz) and is also displayed on the LCD digital display when the stimulation button is pressed.
• Furthermore, a polarity reversal switch offers the options of tonification (-) or sedation (+) treatment.
• A flashing light and sound indicate when point detection is made.
• The spring activated detection prove allows a uniform pressure when searching.
• The grounding circuit is made by holding the metal plate on the side of the unit or with the hand grounding pole.
  
  What's Included:
  
  Pointer Plus Excel features two grounding plates on the unit (allowing use with either left or right hands) as well as a hand probe with grounding pole and attached wire. Two probe tips are included with unit: 2 mm (0.08") and body 4 mm (0.16"). Other standard accessories include 9 volt battery, carrying case, and instructions.
  
  Specifications:
• Output channels: one
• Test load:  500 ohms
• Frequency: 1 to 16 Hz
• Frequency meter: LCD, 0.35"x1.0"
• Volts & current: Normal dial 0 to 22 milliamps
• Volts & current: Blue zone 0 to 2 microamps
• Polarity reversal: +/- by switch
• Pulse width: 220 microseconds
• Pulse shape: asymmetric biphasic square wave
• Pulse modes: continuous
• Measures 6.5" x 1.3" x 0.9"
• Recommended for use by those experienced in acupuncture or acupressure therapy.

<click> to enlarge»
 

Our Price:
$194 + shipping*

The Stimplus II is useful for many conditions.  And best of all the Stimplus II is very easy to use.
 

• Lithium batteries included
• 6 Intensity levels
• 3 Stimulation modes – Continuous, 1Hz, 4 Hz
• Micro-Current
• Earphone included to use in silence
• Audio & Visual Acupoint Detection Indicator
• Audio & Visual (LED) Intensity Indicator
• Timer to adjust

<click> to enlarge»

Our Price:
$194 + shipping*

Temporarily Out of Stock

Acu-Treat – A Great Tool for Practitioners and Students of Acupuncture

Features

• Point location with sensitivity control
• Spring loaded tip (great for stimulating ear points, etc.)
• Combination search/treat button for easy operation
• Variable frequency 1.8Hz to 12Hz
• Variable intensity controller
• Reverse polarity button

Kit includes:

• Hand-held Electro-Acupuncture device
• A carrying case
• Probe with ground
• 9 volt battery
• User’s Instruction Guide
• 400 page book “Guide to Acupuncture”
• Instructional video
• Quick Reference Chart for Acupuncture Points and Meridians

<click> to enlarge»

Our Price:
$294 + shipping*